API 6D Super Duplex Stainless Steel A890 4A Lugged Type Dual Plate Wafer Check Valve

API 594 Dual Plate Wafer Check Valve
 
AEA Dual plate check valve has retainer and retainer-less type design. Dual plate check valves have the advantage of zero leakage toward outside, cost saving. It can be installed in any line orientation, superior seal performance. Valves are designed in accordance to API 594 and have dual plate or single plate design and pin can be retainer-less type.


 
Product Range
-Valve size: 
2" ~ 40" (DN50-DN1000)
-Pressure:
 ANSI Class 150~2500(PN16-PN420) 
-Temperature: 
-196ºC~ 500ºC
-Body Materials:
Carbon Steel, Stainless Steel, Alloy Steel, Duplex Steel
-Trim (Disc/Stem):
Carbon Steel, Stainless Steel, Duplex Steel, Alloy Steel

 
Technical Specifications   
-Design: ASME 16.34/API 594/API 6D
-Face to Face: ASME B16.10
-End Flange: ASME B16.5, ASME B16.47
-BW End: ASME B16.25
-Test: API 598/ API 6D/ BS 6755
-Special: NACE MR-01-75

 
Design Features
-Dual plate or single plate.
-Spring loaded disc.
-Resilient or metal seated.
- Retainer or Retainer Less Design
- Round, Full Lug or Double Flange
-Light-weight & compact design.
-Optional plug disc.

SPRING SELECTION GUIDE 
-Standard Spring Suitable for the line pressure of 0.298MPa through 0.89MPa without any pressure loss and the upward flow direction of vertical installation. 
-Low Coil Spring Ideal for gas with the line pressure of 0.1MPa and under. 
-High Coil Spring Suitable for the line pressure of 0.88MPa.

THE SEAT DESIGN OF DUAL PLATE CHECK VALVE
-No leak, no distortion seals Seat design can be furnished with the resilient seal materials that provide tight seals without leakage and metal seals with minimum leakage.

ADVANTAGE
-Face-to-face dimensions for Dual Plate Wafer Check Valves are about one fourth of a Swing Check Valve. 
-Weight is as little as about 20% of the corresponding Swing Check Valve due to the compact design. 
-Dual Plate Wafer Check Valves have a spring design to close valves more efficiently when the back flow occurs to reduce the water hammer. 
-These valves have the lower pressure drop than Swing Check Valves because of little friction resistance. 
-Dual Plate Wafer Check Valves are less expensive than Swing Check Valves because of the lightness and compact design. These valves are also easier and less expensive to install and maintain because of fewer piping supports and easy handling for installation. 
-Because Dual Plate Wafer Check Valves are flangeless, they are installed between flanges. 
-Normal installation method for horizontal flow is with the hinge pin in vertical position. 
-Installation is available for both horizontal and vertical piping.
APPLICATION
Dual Plate Check Valves have been used successfully in following plants 
- Oil & Gas; 
- Petrol-chemical; 
- Power Generation
 - Refinery; 
- Onshore and Offshore; 
- Chemical Plant; 
- Nuclear; 
- Waste Incineration; 
- Water System; 
- LNG; 
- Shipbuilding; 
- Steel Industry;
 - General industry;






 

Why Choose us?

1.      Factory:Â

AEA VALVE, a specialist manufacturer, established since 2008 and professional production of industrial valves over 10 years.

2.      Regional Sale:Â

We provide specialized sales service refers to different kind of region all over the world. Each sales team member is good at the local language and well experienced to the responsible market. For example: Russian, German, Spanish, Japanese, etc.

3.      Low MOQ:Â

Our factory owns the casting company by itself. We are always ready for providing the sample and producing some small orders, in order to meet the business well.

4.      OEM or Customize:Â

OEM Service or Customized size is Available.Â

5.      We can make the products with the client's demand standard or the custom requirement.

6.      Complete Solution:Â

We are always ready to hear from you, be responding to your enquiry immediately. Our trade manager is always online for you.

7.      High Quality:Â

We have strict quality control system and amounts of testing equipments for different kind of valve, such as size, pressure, working environment etc. We are winning the market reputation with the time goes by.

8.      Quick Delivery:Â

We have the large stock for some hot products.

9.      Competitive Price:Â

10.  We are the manufacturing company which not only has our own manufacturing workshop, but the casting company as well. We provide the straight factory price and service to our customer.

11.  Quality control:

All the products are calibrated with real working condition, and tested before shipping as qualified product.Â

12.  Problem solve:

If you can't solve the problem in your local, please delivery the product to us, we will repair it and then back to you.Â

13.  Integrity: All the warranty and guarantee from us will be put into come true

14.Online Service: any inquiry, please contact with email:  . We will reply you within 12 hours.

API 594 Dual Plate Wafer Check Valve
 
AEA Dual plate check valve has retainer and retainer-less type design. Dual plate check valves have the advantage of zero leakage toward outside, cost saving. It can be installed in any line orientation, superior seal performance. Valves are designed in accordance to API 594 and have dual plate or single plate design and pin can be retainer-less type.


 
Product Range
-Valve size: 
2" ~ 40" (DN50-DN1000)
-Pressure:
 ANSI Class 150~2500(PN16-PN420) 
-Temperature: 
-196ºC~ 500ºC
-Body Materials:
Carbon Steel, Stainless Steel, Alloy Steel, Duplex Steel
-Trim (Disc/Stem):
Carbon Steel, Stainless Steel, Duplex Steel, Alloy Steel

 
Technical Specifications   
-Design: ASME 16.34/API 594/API 6D
-Face to Face: ASME B16.10
-End Flange: ASME B16.5, ASME B16.47
-BW End: ASME B16.25
-Test: API 598/ API 6D/ BS 6755
-Special: NACE MR-01-75

 
Design Features
-Dual plate or single plate.
-Spring loaded disc.
-Resilient or metal seated.
- Retainer or Retainer Less Design
- Round, Full Lug or Double Flange
-Light-weight & compact design.
-Optional plug disc.

SPRING SELECTION GUIDE 
-Standard Spring Suitable for the line pressure of 0.298MPa through 0.89MPa without any pressure loss and the upward flow direction of vertical installation. 
-Low Coil Spring Ideal for gas with the line pressure of 0.1MPa and under. 
-High Coil Spring Suitable for the line pressure of 0.88MPa.

THE SEAT DESIGN OF DUAL PLATE CHECK VALVE
-No leak, no distortion seals Seat design can be furnished with the resilient seal materials that provide tight seals without leakage and metal seals with minimum leakage.

ADVANTAGE
-Face-to-face dimensions for Dual Plate Wafer Check Valves are about one fourth of a Swing Check Valve. 
-Weight is as little as about 20% of the corresponding Swing Check Valve due to the compact design. 
-Dual Plate Wafer Check Valves have a spring design to close valves more efficiently when the back flow occurs to reduce the water hammer. 
-These valves have the lower pressure drop than Swing Check Valves because of little friction resistance. 
-Dual Plate Wafer Check Valves are less expensive than Swing Check Valves because of the lightness and compact design. These valves are also easier and less expensive to install and maintain because of fewer piping supports and easy handling for installation. 
-Because Dual Plate Wafer Check Valves are flangeless, they are installed between flanges. 
-Normal installation method for horizontal flow is with the hinge pin in vertical position. 
-Installation is available for both horizontal and vertical piping.
APPLICATION
Dual Plate Check Valves have been used successfully in following plants 
- Oil & Gas; 
- Petrol-chemical; 
- Power Generation
 - Refinery; 
- Onshore and Offshore; 
- Chemical Plant; 
- Nuclear; 
- Waste Incineration; 
- Water System; 
- LNG; 
- Shipbuilding; 
- Steel Industry;
 - General industry;






 

Why Choose us?

1.      Factory:Â

AEA VALVE, a specialist manufacturer, established since 2008 and professional production of industrial valves over 10 years.

2.      Regional Sale:Â

We provide specialized sales service refers to different kind of region all over the world. Each sales team member is good at the local language and well experienced to the responsible market. For example: Russian, German, Spanish, Japanese, etc.

3.      Low MOQ:Â

Our factory owns the casting company by itself. We are always ready for providing the sample and producing some small orders, in order to meet the business well.

4.      OEM or Customize:Â

OEM Service or Customized size is Available.Â

5.      We can make the products with the client's demand standard or the custom requirement.

6.      Complete Solution:Â

We are always ready to hear from you, be responding to your enquiry immediately. Our trade manager is always online for you.

7.      High Quality:Â

We have strict quality control system and amounts of testing equipments for different kind of valve, such as size, pressure, working environment etc. We are winning the market reputation with the time goes by.

8.      Quick Delivery:Â

We have the large stock for some hot products.

9.      Competitive Price:Â

10.  We are the manufacturing company which not only has our own manufacturing workshop, but the casting company as well. We provide the straight factory price and service to our customer.

11.  Quality control:

All the products are calibrated with real working condition, and tested before shipping as qualified product.Â

12.  Problem solve:

If you can't solve the problem in your local, please delivery the product to us, we will repair it and then back to you.Â

13.  Integrity: All the warranty and guarantee from us will be put into come true

14.Online Service: any inquiry, please contact with email:  . We will reply you within 12 hours.

Steel Lighting Pole High Mast

We have got CE certificate from 2015. We make can manufacture various types of high mast with lifting system for stadium highway parking lot and etc.

Our firm introduced whole set of good-sized numerical control hydraulic folding equipment(1280/16000) as well as equipped with a series of good-sized professional equipments of armor plate-flatted machine, lengthways cut machine, numerical control cut machine, auto-closed up machine, auto-arc-weld machine, hydraulic redressing straight machine, etc. The firm produces all sorts of conical, pyramidal, cylindrical steel poles with production range of dia 50mm-2250mm, thickness 1mm-25mm, once taking shape 16000mm long, and large-scale steel components. The firm also is equipped with a multicolor-spayed pipelining. At the meantime, for better service to the clients, our firm founded a branch com. The Yixing Jinlei Lighting Installation Com, which offers clients a succession of service from design to manufacture and fixing.

Steel Lighting Pole High Mast,30m High Mast Pole, High Mast pole for stadium

Jiangsu Xinjinlei Steel Industry Co., Ltd. , https://www.steelpolejl.com